NEW S-998P 220V 100W Electric Vacuum Double-Pump Solder Sucker Desoldering Gun

NEW S-998P 220V 100W Electric Vacuum Double-Pump Solder Sucker Desoldering Gun
NEW S-998P 220V 100W Electric Vacuum Double-Pump Solder Sucker Desoldering Gun
NEW S-998P 220V 100W Electric Vacuum Double-Pump Solder Sucker Desoldering Gun
NEW S-998P 220V 100W Electric Vacuum Double-Pump Solder Sucker Desoldering Gun

NEW S-998P 220V 100W Electric Vacuum Double-Pump Solder Sucker Desoldering Gun
100% Guarantee - convenient, affordable and easy! Otherwise a random one will be sent. S-998P 220V 100W Electric Vacuum Double-Pump Solder Sucker Desoldering Gun Soldering Iron This gun is very easy for you to desoldering and remove the solder. This device is 2 in 1 unit, including soldering iron and desoldering vacuum pump. Fast heat up function, heated up to 350 C for one minute a stable working temperature and the instantaneous temperature function, suitable for continuous use. Storage Tin glass tube with heat, easily disassembled for easy cleaning. Enhanced double-pump, suction larger, more easily than tin. Transparent back cover, air pump working at a glance. Design horizontal motor pump easy to clean, easy to maintain. Voltage: AC 220V Vacuum: Vibrating membrane Power consumption. Power: 10W Heating Parts:90W ceramic heating core Temperature:350° C 450 ° C Temperature Accuracy:± 2 ° C Arrival time of ma ximum pressure: 0.2 seconds Insulation resistance: 100M Work: Continuous Circuit control system: Zero-interference, the new temperature controller Nozzle Specifications: §1.0mm, §1.5mm, § 2.0mm(1.0mm included only). 1 x S-998P Desoldering gun 1 x Iron stand 2 x Cleaner needle 2 x Filter 1 x1.0 mm Nozzle.

Electric tin gun instruction manual. Vacuum pump: Single pump vibration model. Heating element:80W ceramic heating core. Temperature range:50 450 C.

Suction nozzle standard configuration :1.0. Power line: 1.8 meters, three plug power line. Refer to Photo # 3 + # 4 for details. 1 hold the tin gun tightly with hand, pull the fastening seat (4) backward, and take out the suction canister (9).

2 remove the old filter cotton (5) from the fastening seat (4), place the new filter cotton, and put the suction canister (9) back into the suction gun according to the original method. Unscrew the nut (27), remove the radiator (28), you can take out the suction nozzle (13). 1 The temperature of the suction nozzle of the suction gun is higher. The tin gun holder should be used simultaneously to ensure safety. 2 Suction nozzle temperature is set to 400 degrees, and can be reset according to the need of work.

3 Align the suction nozzle to the removed part first, then pull the button to remove the tin. 4 Before pulling out the plug, be sure to clean the suction nozzle and pipette with a clean needle. New vacuum gun for the first time, because the electric heating element heating, and might have a slight smoke. It will disappear in ten minutes. Can not knock at random, disassemble and install electric and control parts of the parts.

In order to prevent the nozzle from being clogged and difficult to remove, use lubricant or rust inhibitor. When the tin gun is used, a clean needle is used to clean the stannum in the suction nozzle and the suction pipe, and the tin gun is cooled naturally in the air. Residual tin in tin can reduce the efficiency of tin absorption and need to be cleaned up. When the filter cotton is discoloring, it must be replaced immediately. So as not to reduce the tin removal effect.

The item "NEW S-998P 220V 100W Electric Vacuum Double-Pump Solder Sucker Desoldering Gun" is in sale since Saturday, February 25, 2017. This item is in the category "Industrial\Welding & Soldering\Soldering & Desoldering\Soldering Irons". The seller is "ktstoregroup" and is located in Hong Kong.

This item can be shipped worldwide.


NEW S-998P 220V 100W Electric Vacuum Double-Pump Solder Sucker Desoldering Gun