It also can do two-side soldering for the PCB board. The faintness controlling technique and viualization-drawer workbench, make the whole soldering process completed at your observation.
The highly dependable design, make you gratified and reassurance when using it. The device is powered by standard 110VAC 50/60HZ (220VAC Model is available). User interface is implemented by way of T962A input keys and an LCD display.
Pre-Set heating Modes are selected by user interaction with thermal cycle progress observed on LCD display. The T962A may be used to automatically "re-flow" solder to correct bad solder joints, remove/replace bad components and complete small engineering models or prototypes. A windowed drawer is designed to hold the work-piece. Thermal cycle accuracy is maintained by closed loop micro-computer control with infrared heaters, thermocouple and circulating air. (1) Big cubage soldering area.Soldering max area of T-962A is 300×320mm. (2) Many choices of temperature wave. There are eight kinds of temperature parameter waves provided for you to choose, you also can operate the machine with HM-Heating.
And there is cooling fan with the machine. Whole soldering process will be complete automatically. It's very easy to operate. (3) Special heat up and temperature equalization with all design.Output the power reaches to 1500W(T-962A), fast infrared radiation combined with wind-circulation, make the temperature in the drawer more exact and equality. Whole soldering process to be completed automatically according to temperature parameter waves you choose. (4) Humanized science and technology exquisite article. Firm of external appearance, operation with visualization, hail-fellow operation interface, the perfect temperature wave project, from start to eventually display that the science and technology is the root. The simple operating instructions, make you use the machine easily. It will be satisfied to each kind of business enterprise, company extensively develop and the small quantity demand of production. Place the T962A on an appropriate level, insulated work area. Make Sure the work space is well ventilated (exhaust fans may be necessary).
Allow at least 20mm between the T962A and its surroundings for heat protection. Confirm the Work drawer opens and closes smoothly and without obstruction.Locate supplied universal power cord and connect same from rear apron to AC power. Locate and press the power on button, the LCD will light, the T962A will log on. Press s button, the main menu will appear on LCD.
Press F3 button selection different temperature wave. Press F3 button again, can see parameter about you choose the temperature wave. Select: soldering paste sort, soldering temperature, time etc.When selections are complete, then Press F4 button to return previous page. Press the temperature wave that theF1 key carries out to make selection automatically.
When it is ending, the work will shut down automatically, and the warning buzzer is working. In the main menu page, press F2button by handcraft operation. Press F1 button to start cooling, Press F1/S key again to stop. Press F2 button to start heat up, Press F2/S key again to stop.Press the S button to select operational interface after switch on, press the F4 to select a different language category. Following we provide eight different waves, please choose one according to your request. Press the F1/F2 to choose different wave, press F3 to look into different wave parameter, press 4 to confirm the wave you chose. Wave one, use the same with 85Sn/15Pb 70 Sn/30Pb. Wave two, use the same with 63Sn/37Pb 60 Sn/40Pb. Wave three, use the same with Sn/Ag3.5; Sn/Cu 75 Sn/Ag4.0/Cu. Wave four, use the same with Sn/Ag2.5/Cu. Wave five, use the same with The red gum standard is solid to turn temperature wave, Heraeus PD955M. Wave seven & eight, use the same with the wave cycle set-up by yourself. Press s button to the temperature page. Press F1/F2 button, ahead/ backwards select different time. Press F3/F4 button , up/down to select different temperature, Press s button to save. When save finish, press F4 button to select the temperature wave. Press S button to repetition. (1) Lightly puts the product which will be processed in the drawer of the oven on the stage , Close drawer, Press F1 to switch on, The automatic performance make selection of heat wave, Show current performance time, the enactment temperature and temperature on the LCD screen, and automatically note the formed wave of the temperature. (2) The whole process is in your supervision, you may see it by the window of the drawer, and you may see the data from the LCD screen. If the wave doesn't achieve your request, please modify the data by yourself.
(3)The pre-set up wave cycle is according to the temperature that the different solder paste needs. You can pre-set up other wave cycle according to your needs. (4) In the process, you can press "S" to force to stop; When finished, the exhaust fan will work automatically to cool, you also can force to turn on the exhaust fan. (1) To satisfy the need of soldering both sides of the PCB, there is a particular designed fan duct in the machine.
To satisfy the soldering of the small board, please pre-put a PCB board in the size of 10cm10cm, when soldering the small board and the solder-ball. It will make the soldering effect very well.(2) When use the machine, please pre-heat it if the environment is of low temperature, too humidity. The method: after choosing the wave cycle, run the machine with nothing in the drawer at the first time. (3) Attention: The machine can't be used to soldering the chips(the chips which with metal encapsulation are of strong glisten), and the "plastic plug in board" which can't be able to bear the temperature of 250 degree centigrade. (4)About the method to measure the temperature of the machine: Use the standard weatherglass.
Fix the probe on the face of the PCB board(make sure it is the face), then put the PCB board into the drawer, close the drawer. And then you will get the actual temperature. Keep the inside of the machine clear.
When used the machine several times, please turn on the "heat-up" and the "exhaust fan" two or three minutes handly, to make the flux remained in the machine volatilization. It will keep the inside of the machine cleanness, and make the function of the machine stabilization.
Clean the drawer observation glass as necessary. (1)Make sure the power supply is connect with earth. (2)Do not turn off the switch at once after using, make sure the machine is cooling, and then turnn off the switch and cut the power supply.(3)There isn't any way to do smoke evacuation, please put the machine in a ventilated condition to avoid poisoning (when the solder paste volatilization). (4)The insulations in the machine had been treated strictly. Do not take apart the machine until there is any safe protection. The T962A is a self-contained Micro-Processor controlled IC Heater and solder rework station. Uses up to 1500 watts of energy efficient Infrared heating and air circulation to re-flow solder in a large 300×320mm area. Parameters of Eight (8) Soldering cycles are Pre-Defined. Soldering cycles are keypad selected and progress displayed on the T962A LCD.
A single windowed drawer holds assemblies within the heating chamber. The T962A design is ergonomic, practical and easily operated. The entire soldering process is completes automatically from Preheat, Soak and Reflow through cool- down. The T962A is an economical rework solution from single runs to on-demand small batch production. Light weight and a small footprint allows the T962A to be easily bench positioned transported or stored.
The T962A can solder most bosseyed or double-face PCB boards' small parts, ie. CHIPSOPPLCCQFPBGA etc; Can be used to the gum of the product solid, turning the circuit board hot aging, maintaining the PCB board and so on. Be satisfied to the needs of "academe", "smallorder run" and "extensively development of enterprise & company". Soldering max area: 11.8 in×12.6 in. Temperature Range: 212-662 / 100-350.
Size: 17 in×14.6 in×10.2 in. Picking size: 19.7 in ×17 in×13 in. 1 X Main Body (T-962A). 1 X Power Line We stock 110V-240V power version and US.
Plugs for the country all over the world. As a leading and emerging company in manufactory and exporting business, we are specialized in Business and Industrial Products, Sporting Goods, Pet Products, Home and Garden products for more than 10 years. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you.Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. If you have any changes, pls inform us.
These charges are the buyers responsibility. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage.
Used items will not be accepted for return. All emails will be responded to within. You want to cancel an order. If you need further assembly instructions for a product. Any other unspecified questions or concerns.Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it's your fault. A: The item ships from Rancho Cucamonga, CA, United States. A: Please log on your account. Q: How do I return an item?
Please contact our customer service before you return an item. The item "T962A Reflow Oven Infrared IC Heater Visual Operation Micro-Computer Setup New" is in sale since Wednesday, June 5, 2013. This item is in the category "Business & Industrial\CNC, Metalworking & Manufacturing\Welding & Soldering Equipment\Soldering & Desoldering\Soldering Irons". The seller is "bestfashionitem" and is located in Ontario, California. This item can be shipped worldwide.